Broadband-Hamnet™ Forum :: Problems & Answers
Welcome Guest   [Register]  [Login]
 Subject :NanoBridge M2 Cannot save Setup.. 2018-04-17- 21:29:31 
K0BAD
Member
Joined: 2014-04-28- 17:30:15
Posts: 17
Location

I just got ahold of a used NanoBridge M2 and installed the firmware. I cannot get past the setup. When I attempt to save the setup, it responds "error saving setup."


If I intentionally make an error - such as failing to enter a password - it responds with a message that indicates I must enter a password. The generic message is not helpful. Has anybody encountered this before?


I also noted that the device does not have the expected IP address but instead has maintained the default UBIQUITI address.


Should I attempt to re-install the firmware?

IP Logged
 Subject :Re:NanoBridge M2 Cannot save Setup.. 2018-08-30- 18:56:38 
n7ilk
Member
Joined: 2018-08-24- 14:15:06
Posts: 8
Location
Did you ever have any luck getting setup? I'm in the same boat with an AirGrid M2...
IP Logged
 Subject :Re:NanoBridge M2 Cannot save Setup.. 2018-08-30- 21:00:40 
K0BAD
Member
Joined: 2014-04-28- 17:30:15
Posts: 17
Location
I had a more knowledgeable friend look at it. He was able to do it, but had to open up the case and go in on the serial port. It works fine right now...
IP Logged
 Subject :Re:NanoBridge M2 Cannot save Setup.. 2018-08-30- 21:01:31 
K0BAD
Member
Joined: 2014-04-28- 17:30:15
Posts: 17
Location
I had a more knowledgeable friend look at it. He was able to do it, but had to open up the case and go in on the serial port. It works fine right now...
IP Logged
 Subject :Re:NanoBridge M2 Cannot save Setup.. 2018-08-30- 21:01:56 
K0BAD
Member
Joined: 2014-04-28- 17:30:15
Posts: 17
Location
I had a more knowledgeable friend look at it. He was able to do it, but had to open up the case and go in on the serial port. It works fine right now...
IP Logged
 Subject :Re:NanoBridge M2 Cannot save Setup.. 2018-08-31- 06:57:14 
n7ilk
Member
Joined: 2018-08-24- 14:15:06
Posts: 8
Location
Thanks for the response. Looks like I've got to warm up my soldering iron. Thad
IP Logged
 Subject :Re:NanoBridge M2 Cannot save Setup.. 2018-08-31- 19:10:56 
n7ilk
Member
Joined: 2018-08-24- 14:15:06
Posts: 8
Location
Well, now I'm bricked. I guess I can be put in the column of another disappointed newbie that's off to find something else to waste my time on. I can TFTP upload, but I either get "Firmware check failed" or if it will upload, then after resetting goes into a reboot loop. I have tried reloading bbhn as well as Ubiquiti 5.5.11 and even 5.6.6, but nothing gives. Oh well... 73's Thad
IP Logged
 Subject :Re:NanoBridge M2 Cannot save Setup.. 2018-08-31- 19:11:01 
n7ilk
Member
Joined: 2018-08-24- 14:15:06
Posts: 8
Location
Well, now I'm bricked. I guess I can be put in the column of another disappointed newbie that's off to find something else to waste my time on. I can TFTP upload, but I either get "Firmware check failed" or if it will upload, then after resetting goes into a reboot loop. I have tried reloading bbhn as well as Ubiquiti 5.5.11 and even 5.6.6, but nothing gives. Oh well... 73's Thad
IP Logged
Page # 


Powered by ccBoard


SPONSORED AD: